5200 Flowmeter

5200 Flowmeter

The CDI 5200 is a simple to install flowmeter that clamps directly onto the pipe. With two flow-sensing probes are seated directly into the pipe through a 3/16” drilled holes, the 5200 is easily adapted to existing piping systems. One probe senses air temperature while the other keeps 10° above it. Calibrated by pipe size these meters require no set up or adjustment. The easy-to-read digital display can be programmed to read in scfm, m3/min and m3/hr. or daily and cumulative usage. Perfect for outdoor use, this flowmeter is housed in a weather resistant casing and is fully surge protected.... Read more »

5250 Flowmeter Hot Tap

5250 Flowmeter Hot Tap

The CDI 5250 makes installation under pressure quick and easy, with no system shut down needed. Two probes are run directly though valves and a muffler that will filter the particles caused from drilling. One probe senses air temperature while the other keeps 10° above it. The entire installation process takes only a few minutes and is easily adapted to existing piping systems. Calibrated by pipe size these meters require no set up or adjustment. The easy-to-read digital display is simple to rotate based on pipe orientation and can be programmed to read in scfm, m3/min and m3/hr. or daily... Read more »

5400 Flowmeter

5400 Flowmeter

The CDI 5400 is a simple to install flowmeter that clamps directly onto the pipe, with no cutting or welding required. With two side-by-side flow-sensing probes in a single ring configuration, seated directly into the pipe through a small, drilled hole, the 5400 is easily adapted to existing piping systems. One probe senses air temperature while the other keeps 10° above it. Calibrated by pipe size these meters require no set up or adjustment. The easy-to-read digital display can be programmed to read in scfm, m3/min and m3/hr. or daily and cumulative usage. The 5400 is built for larger pipe... Read more »

5450 Flowmeter Hot Tap

5450 Flowmeter Hot Tap

The CDI 5450 makes installation under pressure quick and easy, with no system shut down needed. Two probes are run directly though valves and a muffler that will filter the particles caused from drilling. One probe senses air temperature while the other keeps 10° above it. The entire installation process takes only a few minutes and is easily adapted to existing piping systems. Calibrated by pipe size these meters require no set up or adjustment. The easy-to-read digital display is simple to rotate based on pipe orientation and can be programmed to read in scfm, m3/min and m3/hr or daily... Read more »

Pressure Sensing Option (PSO)

Pressure Sensing Option (PSO)

The Pressure Sensing Option for the 5200 and 5400 flow meter monitors the pressure and flow of the air in the system. Mounted next to the flow sensing probes the pressure sensor will access the pressure through a cut-out gasket in the pipe. Using a cut-out gasket and placed next to the probes the PSO will measure the pressure.

CDI 5200 SRD Summing Remote Display

CDI 5200 SRD Summing Remote Display

Use for daily and cumulative usage display or as a remote display for a meter that is in a difficult to view location. The 5200-SRD comes with three display modes, Rate, Daily and Cumulative usage. Simple push button control. Connects to the main display using 3- connector cable.

CDI 5200 AVD Average Remote Display

CDI 5200 AVD Average Remote Display

Display the rolling average usage from one minute to one hour. Usage is more accurately measured with a steady average then a fluctuating display.

Drill Guides

Drill Guides

Be sure that drill holes are correctly aligned with Drill Guides. Comes with 3/16” bit and Allen wrenches needed for installation.

Blocking Rings

Blocking Rings

Once flow meter is removed, Blocking Rings will cover the holes to prevent air leaks. Available for copper and steel piping or OD tubing, ½” to 8”.